data sheet part number 856592 140 mhz saw filter subject to change or obsolescence without notice rev a 06-07 triquint semiconductor, inc. page 1 of 5 features ? for multi carrier wcdma applications ? usable 1.0 db bandwidth of 18.4 mhz ? low loss ? high attenuation ? single-ended operation, 50 ? ? ceramic surface mount package (smp) ? hermetic ? rohs compliant (2002/95/ec), pb -free ? package pin configuration surface mount 13.30 x 6.50 x 1.75 mm bottom view 12 11 10 9 8 7 6 5 4 3 2 1 pin no. description 5 output 11 input 6,12 to be grounded 1,2,3,4 case ground 7,8,9,10 case ground 1.75 nom. 1.96 max. 0.76 0.79 1.17 x 3.76 1.50 2.54 6.50 2.18 2.54 13.3 dimensions shown are nominal in millimeters all tolerances are 0.15mm except overall length and width 0.10mm body: al 2 o 3 ceramic lid: kovar , ni plated terminations: au plating 0.5 - 1.0 m, over a 2 - 6 m ni plating pb
data sheet part number 856592 140 mhz saw filter subject to change or obsolescence without notice rev a 06-07 triquint semiconductor, inc. page 2 of 5 electrical specifications (1) operating temperature range: (2) -30 to +80 o c parameter (3) minimum typical maximum unit center frequency, f o - 140 - mhz insertion loss @ f o - 9.3 11 db 1.0 db bandwidth (4) - 20.7 - mhz lower 1.0 db bandedge - 129.7 130.8 mhz upper 1.0 db bandedge 149.2 150.4 - mhz 3.0 db bandwidth (4) - 21.6 - mhz lower 3.0 db bandedge - 129.3 130.2 mhz upper 3.0 db bandedge 149.8 150.9 - mhz 35 db bandwidth (4) - 24.4 - mhz lower 35 db bandedge 126.8 128.0 - mhz upper 35 db bandedge - 152.4 153.2 mhz passband ripple (5) over the 1 db bandwidth - 0.5 0.8 db group delay ripple 130.8 - 149.2 mhz - 100 150 nsec absolute delay - 1 - sec relative attenuation (4) 10 - 90 mhz 90 - 120 mhz 120 - 126.8 mhz 153.2 - 160 mhz 160 - 190 mhz 190 - 800 mhz 35 40 35 35 40 35 55 53 45 39 49 58 - - - - - - db db db db db db input vswr 130.8 - 149.2 mhz - 2.0 2.5 - output vswr 130.8 - 149.2 mhz - 1.8 2.3 - source/load impedance (6) - 50 - ? notes : 1. all specifications are based on the test circuit shown below 2. in production, devices will be tested at room temperature to a guardbanded specific ation to ensure electrical compliance ove r temperature 3. electrical margin has been built into the design to account for the variations due to manufacturing tolerances 4. all attenuation m easurements are referenced from loss at f o 5. describes the maximum peak to adjacent valley va riation over the passband (not including roll-off). 6. this is the optimum impedance in order to achieve the performance shown test circuit: actual matching values may vary due to pcb layout and parasitics 50 ? single-ended input 1,2,3,4,6 7,8,9,10,12 50 ? 150nh 11 5 15nh 50 ? 150nh 68pf 50 ? single-ended output
data sheet part number 856592 140 mhz saw filter subject to change or obsolescence without notice rev a 06-07 triquint semiconductor, inc. page 3 of 5 typical performance (at +25 o c)
data sheet part number 856592 140 mhz saw filter subject to change or obsolescence without notice rev a 06-07 triquint semiconductor, inc. page 4 of 5 matching schematics actual matching values may vary due to pcb layout and parasitics 50 ? single-ended input 1,2,3,4,6 7,8,9,10,12 50 ? 150nh 11 5 15nh 50 ? 150nh 68pf 50 ? single-ended output marking pcb footprint xxxxxx date code id dot sawtek 856592 1.70 13.51 .99 1.55 8.61 3.53 .99 1.70 6.70 the date code consists of: day of the current year (julian, 3 digits), last digit of the year (1 digit) and hour (2 digits) this footprint represent s a recommendation only dimensions shown are nominal in millimeters tape and reel a a 24 1.75 11.5 ?1.5 2.3 13.9 4.0 ?1.5 2.0 0.3 12.0 7.1 section a-a direction of travel ?330 24.8 2.7 ?102 ?13.0 ?20.2 2.0 id dot dimensions shown are nominal in millimeters packaging quantity: 2000 units/reel
data sheet part number 856592 140 mhz saw filter subject to change or obsolescence without notice rev a 06-07 triquint semiconductor, inc. page 5 of 5 maximum ratings parameter symbol minimum maximum unit operating temperature range t -30 +80 o c storage temperature range t stg -40 +85 o c important notes warnings ? electrostatic sensitive device (esd) ? avoid ultrasonic exposure rohs compliance ? this product complies with eu directive 2002/95/ec (rohs) solderability ? compatible with jedec j-std-020c pb -free process, 260c peak reflow temperature ( see soldering profile ) links to additional technical information pcb layout tips qualification flowchart soldering profile s-parameters rohs information other technical information triquint?s liability is limited only to the surface acoustic wave (saw) component(s) described in this data sheet. triquint do es not accept any liability for a pp lications, p rocesses, circuits or assemblies, which are im p lemented usin g an y triquint com p onent described in this data sheet. contact information po box 609501 orlando, fl 32860-9501 usa phone: +1 (407) 886-8860 fax: +1 (407) 886-7061 email: info-product@tqs.com web: www.triquint.com or contact one of our worldwide network of sales offices, representatives or distributors pb
|
